Showing 1–16 of 86 results

  • 1.5I 7 SEG LOP (1.5”)

    • Supply voltage requirement 12VDC/24VDC as per customer requirement.
    • Single digit 1.5 inch 7 segment display is used for elevator floor Indicator.
    • Single 1.5 inch UP & DOWN arrow module is used for elevator direction indication.

  • 16X16 COP INDICATOR

    • Supply voltage 12VDC/24VDC as per customer requirement.
    • Five 1 inch ( 8X8 ) DOT MATRIX modules are used in this card. 
    • One 8X8 Dot Matrix is used for showing elevator direction indication with the scrolling Arrow.
    • All inputs are -ve (GND).

  • 230VAC TO 110VDC

    • Supply voltage requirement 230VAC.
    • This card converts 230VAC supply to 110VDC supply.

  • 7 SEG TO SERIAL CONVERTER

    • Supply voltage requirement 12VDC TO 24VDC.
    • This card converts 7 Segment input data to our Serial protocol communication data.
    • No floor set setting is required for Serial LOP & COP indicators.

  • ARD 3 PHASE

    • Direct MOTOR driving ARD logic board, so we can use with DOL (single speed) & V3F control elevator.
    • Nominal battery voltage require 48VDC
      (12VDC, 7Ah four batteries)
    • Maximum capacity up to 10KW (15HP).
    • Output voltage 48V 3PHASE (4-6Hz).
    • Inbuilt Battery charger.
    • Direction selection according to light load.

  • ARD ANNOUNCEMENT

    • Operating voltage from 12V TO 24V AC/DC.
    • Compact & designer box with 8 ohm speaker.
    • Easy volume control with external POT.

  • ARD BIG-48V

    • High reliability with microcontroller based pure sine wave technology.
    • Operating Voltage 48VDC (12VDC, 4 Batteries )
    • Maximum 3500VA output can be generated.
    • We can use the same card for Single phase & Two phase outputs by just changing the transformer design.
    • Efficiency is greater than 85%.

  • ARD LED INDICATOR

    • ARD LED INDICATOR card used with the ARD BIG-48 & ARD SMALL-48V logic boards.
    • This card has one COM-NO switch used for the ARD system ON & OFF with Relimate connector output.

  • ARD SMALL-48V

    • Operating Voltage 48VDC (12VDC, 4 Batteries ).
    • Compact size design suitable for small size control panels.
    • Maximum 2000VA output can be generated.

  • ARROW 7 SEG LOP (1”)

    • Supply voltage requirement 12VDC/24VDC as per customer requirement.
    • Single digit & double digit 1 inch 7 segments are used for the elevator floor Indicator.

  • ARROW 7 SEG LOP(0.8”)

    • Supply voltage requirement 12VDC/24VDC as per customer requirement.
    • Single digit & double digit 0.8 inch 7 segments are used for the elevator floor Indicator.

  • BIG COP DDM

    • Supply voltage 12VDC/24VDC as per customer requirement.
    • Three 2 inch ( 5×7 ) DOT MATRIX modules are used in this card. One Dot Matrix is used for showing elevator direction indication with the scrolling Arrow & another two dot matrix are used for up to two digit floor indicator.

  • BIG COP INDICATOR

    • Supply voltage requirement 12VDC/24VDC as per customer requirement.
    • Single digit & double digit 1.5 inch 7 segments are used for the elevator floor Indicator.
    • This card also shows time & temperature with the small 7 segments.

  • BIG RN ARROW IND

    • Supply voltage requirement 12VDC/24VDC as per customer requirement.
    • Single digit & double digit 1.5 & 2 inch 7 segments are used for the elevator floor Indicator.
    • Single 2 inch ( 5×7 ) DOT MATRIX module is used for showing elevator direction indication with the scrolling Arrow.

  • COP F-L-S-A

    • Supply voltage requirement 12VDC.
    • Relay card used for the Normal push to ON switch COP with all 12V/24V buttons.
    • All Relays COM-NO-NC contacts are connected to the output connector with the MOV protections.

  • CYPRESS TOUCH

    • Capacitive Touch Button solution for LOP & COP.
    • Supply Voltage Requirement 12VDC.